Chief Manufacturing TV Mount PRO 2000 User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Large Flat Panel Wall Mount  
Model: PRO-2000 Series  
PRO-2000 Series Wall Mount Features:  
Accommodates large flat screens weighing up to  
200 lbs (90.7 kg).  
Mounting brackets adapt to either 16" or 24" on  
center dual stud wood framework; integrated  
lateral shift adjusts ± 4.5" (16" on center) or ± 0.5"  
(24" on center).  
Infinite tilt and lock adjustment between 0-15  
degrees.  
Chief's exclusive Q-Latch mounting system  
provides convenient and secure display connect/  
disconnect; optional padlock provides additional  
display security.  
®
Q-Latch is a registered trademark of Chief Mfg.  
! IMPORTANT: If the installation of this product requires  
OSHPD seismic approval, refer to OSHPD pre-approval  
documents and drawings before beginning installation.  
OSHPD documents and drawings are available at  
www.chiefmfg.com, and are also located on the product  
information page for the mount.  
PRO-2000 Series  
BEFORE YOU BEGIN  
CAUTION: To prevent damage to your monitor and PRO-2000, which could affect or void the Factory warranty,  
thoroughly study all instructions and illustrations before you begin to install the mount. Pay particular attention to the  
Warnings and Cautions in this document.  
The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor  
the mount must be capable of supporting five times the total weight of the equipment.  
The maximum weight to be installed on the PRO-2000 wall mount is 200 lbs (90.7 kg).  
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-  
6480.  
8805-000140 (Rev. E)  
CHIEF MANUFACTURING INC.  
1-800-582-6480 952-894-6280 FAX 952-894-6918  
8401 EAGLE CREEK PARKWAY, STE 700  
SAVAGE, MINNESOTA 55378 USA  
¤2007 Chief Manufacturing  
10/07  
 
Installation Instructions  
TOOLS REQUIRED FOR INSTALLATION  
Drill and drill bit set  
Socket wrench set  
NOTE: Other tools may be required depending on your method of installation.  
PARTS  
Unpack carton, inspect and verify contents.  
Read installation instructions completely. If any listed  
parts are missing, contact Chief Customer Service at  
1-800-582-6480.  
10  
20 - 4 Lag Bolts  
Table 1: Parts  
10  
20  
30  
MOUNT, PRO-2000 Series  
1
4
4
BOLT, Lag, 5/16" x 2-½"  
WASHER, 5/16"  
30 - 4 Washers  
3
 
Installation Instructions  
Wood Studs  
INSTALLATION  
MOUNT INSTALLATION  
WARNING: It is the responsibility of the installer to  
verify that the wall to which the mount is anchored will  
safely support the combined load of all attached  
components and equipment.  
Wall  
1. Determine approximate mounting location, keeping in  
mind the display size.  
NOTE: The mount is to be installed on dual wood studs  
or other equivalent vertical or horizontal  
supporting framework.  
Pilot Holes  
2. Use a stud sensor to locate the two wood studs. Mark  
locations with a pencil.  
3. With mount at desired height and located between the  
marked studs, temporarily hang mount on wall by  
installing a nail through the triangular hole located in  
the center of the mount (See Figure 1). Ensure mount  
is oriented such that pitch adjustment arms are at top  
of mount.  
Figure 2  
Wood Studs  
4. Level the mount and use a pencil to mark the location  
of the four pilot holes. Ensure marks are in the center  
of wood studs.  
5. Remove mount from wall.  
6. Drill four pilot holes using a 7/32" drill bit. Make sure  
pilot holes are straight (See Figure 2).  
7. While holding mount against wall, select appropriate  
mounting holes:  
16" on center studs: The mount can be installed  
centered between the studs as shown (See  
Figure 3), or it can be installed to the left or right  
of center (See Figure 4).  
24" on center studs: The mount must be centered  
between the studs (See Figure 5).  
8. Install four 5/16" x 2-½" lag bolts (20) and four 5/16"  
washers (30) through mounting holes and into pilot  
holes. Tighten all lag bolts.  
Insert nail here  
Figure 3  
Figure 1  
4
 
Installation Instructions  
If an interface bracket for the display being mounted  
needs to be obtained, or additional assistance is  
required, contact a Chief Customer Service  
representative by calling 1-800-582-6480 or by visiting  
Wood Studs  
(Left of Center Install)  
To install the display:  
1. Two Q-latches are installed on this mount. Make sure  
both Q-Latches are in the UNLATCHED position  
(See Figure 6).  
Faceplate  
UNLATCHED  
Wood Studs  
(Right of Center Install)  
Q-Latch  
Figure 4  
Figure 6  
2. While supporting each side of the display, align the four  
mounting buttons on the interface bracket with the four  
teardrop slots in mount faceplate. Lower bracket firmly  
into slots. (See Figure 7)  
Wood Studs  
Faceplate  
Display  
Mounting  
Button  
Faceplate  
Display  
Figure 5  
DISPLAY INSTALLATION  
The following procedure assumes that the proper  
interface bracket for the display being mounted has  
already been installed on the display.  
Mounting  
Button  
If no interface bracket is present on display, install  
bracket to display using the instructions included with the  
interface bracket before proceeding.  
Figure 7  
5
 
Installation Instructions  
Tilt Adjustment Nuts  
3. Secure display by rotating both Q-Latches to the fully  
LATCHED position (See Figure 8). If one or both Q-  
Latches do not fully engage, ensure the mounting  
buttons are fully seated in the teardrop slots.  
NOTE: A hole is provided in the Q-Latch and faceplate  
to accommodate the insertion of a padlock or  
similar locking device.  
Faceplate  
Display  
LATCHED  
Mounting  
Button  
Figure 9  
Q-Latch  
Figure 8  
TILT ADJUSTMENT  
CAUTION: Loosen the nut only. To avoid equipment  
damage, do not remove the nut from the mount.  
1. Using 1/2" socket wrench, loosen the tilt adjustment  
nut on both arms of the mount (See Figure 9).  
CAUTION: Do not over-tighten the nuts. Over-  
tightening the nuts may cause excessive wear and may  
damage your mount.  
2. Tilt display to the desired position. Tighten both nuts.  
REMOVE THE DISPLAY  
1. Disconnect all power/audio/video cables.  
2. UNLATCH both Q-Latches to unlock the display (See  
Figure 8).  
3. With the aid of another person, lift the display up and  
out of the teardrop slots in the mount.  
6
 

Bissell Vacuum Cleaner 3525 User Manual
Black Box Network Hardware NBS008A User Manual
Bose Portable Speaker 2 User Manual
Boss Audio Systems Carrying Case MR1420S User Manual
Bradford White Corp Water Heater 544 B User Manual
Briggs Stratton Air Cleaner 441700 Series User Manual
Brookstone Automobile Accessories 643494 User Manual
Bushnell Binoculars 1111024 User Manual
Cateye Bicycle Accessories CC 8000 User Manual
Chevrolet Automobile 2010 Silverado Hybrid User Manual