Chief Manufacturing Network Card CTA 100 User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
CTA-100  
VCR / DVD / Cable Box Adapter  
The CTA-100 provides a centralized mounting  
solution for a VCR/DVD/cable box.  
The shelf on the CTA-100 can be adjusted to fit the  
width and height of most VCR/DVD/Cable Boxes.  
The maximum weight capacity for the CTA-100 is  
50lbs. (22.7 kg).  
The CTA-100 was specifically designed to mount  
underneath any CTV Series TV/Monitor mount.  
Depending upon the weight limitations of the  
TV/Monitor mount, the CTA-100 is a stackable  
unit. Up to three CTA-100 units can be stacked.  
The weight of the stacked units cannot exceed  
50lbs. (22.7 kg).  
BEFORE YOU BEGIN  
CAUTION: To prevent damage to your equipment, which could affect or void the Factory warranty,  
thoroughly study all instructions and illustrations before you begin to install the CTA-100. Pay particular  
attention to the Warnings and Cautions in this document.  
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or  
952-582-6480.  
CHIEF MANUFACTURING INC.  
8809-000022 (Rev. A)  
1-800-582-6480 952-894-6280 FAX 952-894-6918 2004 Chief Manufacturing  
8401 EAGLE CREEK PARKWAY, STE. 700  
SAVAGE, MINNESOTA 55378 USA  
10/04  
 
Installation Instructions  
CTA-100  
IMPORTANT WARNINGS and CAUTIONS!  
WARNING  
CAUTION  
WARNING  
A WARNING alerts you to the possibility of serious injury or death if you do not  
follow the instructions.  
A CAUTION alerts you to the possibility of damage or destruction of equipment if you do  
not follow the corresponding instructions.  
Improper installation can result in serious personal injury! Make sure that the  
mounting surface can support a redundant weight factor five times the total weight of  
the equipment: if not, reinforce the mounting surface structural members before  
installing the mount.  
WARNING  
WARNING  
Be aware of the potential for personal injury or damage to the equipment if it is not  
adequately mounted. Refer to the specifications described in Table 1, on page 2.  
The installer is responsible for verifying that the mounting surface to which the  
mount is anchored will safely support the combined load of all attached components or  
other equipment.  
WARNING  
The combined weight of the equipment placed on the CTA-100 must not exceed the  
maximum support weight of the mount. Refer to the specifications described in Table 1,  
on page 2.  
WARNING  
CAUTION  
Watch for pinch points. Do not put your fingers between movable parts.  
Check the unit for shipping damage before you begin the installation.  
CONTENTS  
CTA-100 SPECIFICATIONS...........................................2  
TOOLS REQUIRED FOR INSTALLATION..................4  
SHIPPING CONTENTS...................................................4  
PARTS ..............................................................................4  
INSTALLATION INSTRUCTIONS................................5  
Assembling the Center Plates and Side Plates...............5  
Attaching the Center Plates and Side Plates..................5  
Installing Pads on Adjustment Plates ............................6  
Installing Adjustment Plates..........................................6  
Installing Top Attachment Plate....................................7  
Connecting CTA-100 to TV/Mount..............................7  
Making Adjustments .....................................................8  
Stacking Two Units.......................................................9  
Stacking Three Units.....................................................9  
3
 
Installation Instructions  
CTA-100  
SHIPPING CONTENTS  
BEFORE PROCEEDING: Unpack the carton.  
Verify contents listed in Table 2.  
TOOLS REQUIRED FOR  
INSTALLATION  
The tools required for installation are as follows:  
Read installation instructions completely. If you are  
missing any of the listed components, contact  
Customer Service at: 1-800/582-6480.300.  
Allen Wrench (supplied)  
NOTE: Other tools may be required depending on your  
method of installation.  
Table 2. CTA-100 Parts List  
ITEM DESCRIPTION  
QTY  
10  
20  
30  
40  
50  
60  
70  
80  
Top Attachment Plate  
Center Plate  
1
2
Side Plate  
2
Adjustment Plate  
Foam Pad  
2
2
M5 X 8mm Button Head Cap screw  
Flat Washer  
20  
20  
1
Allen Wrench  
PARTS  
20  
40  
10  
60  
70  
80  
30  
50  
Figure 1. CTA-100 Component Parts  
4
 
Installation Instructions  
CTA-100  
INSTALLATION INSTRUCTIONS  
STEP 1  
30  
20  
30  
20  
Figure 2. Assemble Center Plates and Side Plates  
Assembling the Center Plates and Side Plates  
Assemble center plates and side plates, as follows:  
1. Locate two center plates (20) and two side plates  
(30). See Figure 2.  
NOTE: The two side plates fit inside the two center  
plates. To assemble the unit, slide the two side  
plates into the cuffed center plates.  
2. Interconnect the first side plate (30) with both center  
plates (20) as shown in Figure 2.  
(70)  
3. Repeat step 2 to interconnect the second side plate  
(30) with the center plates (20).  
Attaching the Center Plates and Side Plates  
Attach center plates and side plates, as follows:  
1. On the top, install four flat washers (70) and four  
M5 X 8mm button head cap screws (60) into the  
threaded holes in the side plates (30). See Figure 3.  
(60)  
Figure 3. Attach Center Plates and Side Plates  
2. Repeat step 1 to attach the side plates on the bottom  
of the unit.  
NOTE: The screws can be adjusted later when the  
width of the VCR/DVD is apparent.  
5
 
Installation Instructions  
CTA-100  
Installing Pads on Adjustment Plates  
STEP 2  
Install foam pads on adjustment plates, as follows:  
ADJUSTMENT  
PLATE (40)  
1. Locate two foam pads (50) and two adjustment  
plates (40). See Figure 4.  
(50)  
INSTALL FOAM  
PAD (50) TO  
2. Remove protective tape from foam pad (50) to  
expose the bond side.  
UNDERSIDE OF  
TOP ADJUSTMENT  
PLATE OF (40).  
3. Install foam pad (50) on underside of top adjustment  
plate (40).  
4. Repeat steps 2 and 3 to install the foam pad (50) on  
the second adjustment plate (40).  
Figure 4. Install Pads on Adjustment Plates  
Installing Adjustment Plates  
(70)  
Install top adjustment plates, as follows:  
ADJUSTMENT PLATE (40)  
1. Install two flat washers (70) and two M5 X 8mm  
button head cap screws (60) into the threaded holes  
in the side plates (30). See Figure 5.  
2. Repeat step 1 to install the second adjustment plate.  
NOTE: The screws can be adjusted later when the  
height of the VCR/DVD is apparent.  
(60)  
Figure 5. Install Adjustment Plates  
6
 
Installation Instructions  
CTA-100  
STEP 3  
Installing Top Attachment Plate  
Install top attachment plate, as follows:  
1. Locate the top attachment plate (10).  
WARNING  
Failure to install and tighten the screws  
securing the top attachment plate can result in  
personal injury and/or equipment damage.  
(10)  
(70)  
(80)  
2. Install four flat washers (70), four M5 X 8mm  
button head cap screws (60), and the top  
attachment plate (10) onto the bottom of the  
TV/Monitor mount as shown in Figure 6.  
Tighten the screws.  
Figure 6. Install Top Attachment Plate  
Connecting CTA-100 to TV/Mount  
Connect the CTA-100 to the TV/Mount, as  
follows:  
(TV/Mount)  
1. Align CTA-100 with top attachment plate  
(10) as shown in Figure 6.  
2. Install four flat washers (70), four M5 X 8mm  
button head cap screws (60) into the top  
attachment plate (10). Tighten the screws.  
See Figure 7.  
(CTA-100)  
Figure 7. Connect CTA-100 to TV/Mount  
7
 
Installation Instructions  
CTA-100  
Making Adjustments  
STEP 4  
1. Install your VCR/DVD into the CTA-100.  
2. Adjust the side plates (30) and adjustment plates (40)  
as needed to secure your VCR/DVD safely in the  
CTA-100. See Figure 8.  
3. Tighten all cap screws (60).  
WARNING  
Failure to install and tighten the screws to secure  
your VCR/DVD can result in personal injury and/or  
equipment damage.  
(40) and (30)  
4. Check the CTA-100 to ensure that the side plates  
(30) and adjustment plates (40) are adjusted  
correctly. The unit should fit tightly around your  
VCR/DVD. If not, repeat steps 2 and 3 until your  
VCR/DVD is secure.  
Figure 8. Make Adjustments to Unit  
8
 
Installation Instructions  
CTA-100  
STEP 5 (OPTIONAL)  
(10)  
(70)  
(80)  
CONNECT SECOND ATTACHMENT PLATE  
TO BOTTOM CENTER PLATE OF CTA-100.  
Figure 9. Install Second Attachment Plate  
Stacking Two Units  
6. Tighten all cap screws (60).  
Stack two units, as follows:  
WARNING  
1. Locate the top attachment plate (10) for the second  
unit.  
Failure to install and tighten the screws to secure your  
VCR/DVD can result in personal injury and/or  
equipment damage.  
CAUTION  
The stacked load cannot exceed 50lbs. (22.7kg).  
7. Check the CTA-100 to ensure that the side plates (30)  
and adjustment plates (40) are adjusted correctly. The  
unit should fit tightly around your VCR/DVD. If not,  
repeat steps 5 and 6 until your VCR/DVD is secure.  
2. Install the second attachment plate (10) on the center  
plate (20) of the first CTA-100 unit. Use four flat  
washers (70) and four M5 X 8mm button head cap  
screws (60). Tighten the screws. See Figure 9.  
3. Attach the second CTA-100 to the second attachment  
plate (10). Use four flat washers (70), four M5 X 8mm  
button head cap screws (60). Tighten the screws.  
Stacking Three Units  
Stack three units, as follows:  
4. Install your VCR/DVD into the CTA-100.  
1. Perform the “Stacking Two Units” procedure to install  
the third CTA-100.  
5. Adjust the side plates (30) and adjustment plates (40)  
as needed to secure your VCR/DVD safely in the  
CTA-100.  
CAUTION  
Do not stack more than three VCR/DVD mounts from  
a TV/Monitor mount. The stacked load cannot exceed  
50lbs. (22.7kg).  
2. Verify that all three units are secure.  
9
 

Bionaire Fan BFH6616 User Manual
Black Decker Oven TR200M User Manual
Black Decker Paint Sprayer BDPH200 User Manual
Black Decker Trimmer LST300 User Manual
Blanco Indoor Furnishings 500 340 User Manual
Bosch Appliances Clothes Dryer WTC82100US User Manual
Briggs Stratton Blower 114900 to 114999 User Manual
Brother Sewing Machine XL 5510 User Manual
Canon Printer C3380 Series User Manual
Channel Plus Stereo Amplifier MDS 6 User Manual