Chief Manufacturing Network Card CMA351 User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Instrucciones de instalación  
Installationsanleitung  
Istruzioni di installazione  
Installatie-instructies  
Instruções de Instalação  
Instructions d´installation  
Heavy Duty Swivel Adapter  
Spanish Product Description  
German Product Description  
Portuguese Product Description  
Italian Product Description  
Dutch Product Description  
French Product Description  
CMA351  
 
Installation Instructions  
CMA351  
LEGEND  
Tighten Fastener  
Pencil Mark  
Apretar elemento de fijación  
Befestigungsteil festziehen  
Apertar fixador  
Marcar con lápiz  
Stiftmarkierung  
Marcar com lápis  
Segno a matita  
Potloodmerkteken  
Marquage au crayon  
Serrare il fissaggio  
Bevestiging vastdraaien  
Serrez les fixations  
Loosen Fastener  
Drill Hole  
Aflojar elemento de fijación  
Befestigungsteil lösen  
Desapertar fixador  
Perforar  
Bohrloch  
Fazer furo  
Praticare un foro  
Gat boren  
Allentare il fissaggio  
Bevestiging losdraaien  
Desserrez les fixations  
Percez un trou  
Phillips Screwdriver  
Adjust  
Destornillador Phillips  
Ajustar  
Kreuzschlitzschraubendreher  
Chave de fendas Phillips  
Cacciavite a stella  
Einstellen  
Ajustar  
Regolare  
Afstellen  
Ajuster  
Kruiskopschroevendraaier  
Tournevis à pointe cruciforme  
Open-Ended Wrench  
Llave de boca  
Remove  
Quitar  
Gabelschlüssel  
Chave de bocas  
Chiave a punte aperte  
Steeksleutel  
Entfernen  
Remover  
Rimuovere  
Verwijderen  
Retirez  
Clé à fourche  
By Hand  
Optional  
Opcional  
Optional  
Opcional  
Opzionale  
Optie  
A mano  
Von Hand  
Com a mão  
A mano  
Met de hand  
À la main  
En option  
Hex-Head Wrench  
Security Wrench  
Llave de cabeza hexagonal  
Sechskantschlüssel  
Chave de cabeça sextavada  
Chiave esagonale  
Llave de seguridad  
Sicherheitsschlüssel  
Chave de segurança  
Chiave di sicurezza  
Veiligheidssleutel  
Clé de sécurité  
Zeskantsleutel  
Clé à tête hexagonale  
3
 
CMA351  
Installation Instructions  
TOOLS REQUIRED FOR INSTALLATION  
3/32"  
5/32"  
(provided)  
(provided)  
PARTS  
A (1)  
B (1)  
D (2)  
10-24  
F (1)  
5/16-18 x 3/8"  
C (2)  
.315 x .507 x 090  
E (1)  
#8-32 x 1/2"  
G (1)  
10-24 x 1/4"  
H (1)  
3/32"  
J (1)  
5/32"  
4
 
Installation Instructions  
CMA351  
5. Secure Swivel Adapter (A) to 1 ½" NPT pipe using one Set  
Screw (F) and hex wrench. (See Figure 2)  
Installation  
IMPORTANT ! : The following installation procedure  
assumes that a 1 ½" NPT pipe has been properly  
installed to the ceiling.  
1. Place one Nylon washer (C) over each stud on Swivel  
Adapter (A). (See Figure 1)  
2. Align slots in stop plate (B) with two threaded studs on  
Swivel Adapter (A). (See Figure 1)  
(F) X1  
3. Secure Stop plate (B) to Swivel Adapter (A) using two lock  
nuts (D). (See Figure 1)  
4
NOTE: DO NOT fully tighten lock nuts at this time.  
5
(B) X1  
2
(A) X1  
(C) X2  
Figure 2  
1
6. Rotate the bottom of Swivel Adapter (A) until middle set  
screw in swivel adapter (A) makes contact with tab in stop  
plate (B). (See Figure 3)  
(A) X1  
NOTE: This is considered the first stop position.  
Tab  
(Not Visible)  
6
Lower Set  
Screw  
(D) X2  
3
(B) X1  
(A) X1  
(A) X1  
Tab  
Lower Set  
Screw  
TOP VIEW  
Figure 1  
4. Thread Swivel Adapter (A) onto existing 1 ½" NPT pipe.  
(See Figure 2)  
Figure 3  
5
 
CMA351  
Installation Instructions  
7. Thread one 1 1/2" NPT pipe into lower Swivel Adapter (A).  
(See Figure 4)  
8. Secure lower 1 1/2" NPT pipe to swivel adapter (A) using  
one set screw (G). (See Figure 4)  
(E) X1  
WARNING: Exceeding the weight capacity can result in  
serious personal injury or damage to equipment! It is the  
installer’s responsibility to make sure the combined weight of  
all components located between the CMA351 up to (and  
including) the display/projector does not exceed 500 lbs  
(226.8 kg).  
The weight capacity of the CMA351 may be LIMITED to  
the lowest weight capacity of any other component located  
between the CMA351 and the supporting structure!  
(B) X1  
Second Stop Location  
X1  
Figure 5  
6
11. Tighten two lock nuts (D). (See Figure 6)  
X1  
(D) X2  
Figure 4  
9. Rotate the bottom portion of the CMA-351 to the desired  
location for the second stop (0 degrees to 330 degrees).  
(See Figure 5)  
10. Insert one Phillips pan head screw (E) in the nearest  
threaded hole in stop plate (B). (See Figure 5)  
Figure 6  
6
 
Installation Instructions  
CMA351  
7
 
CMA351  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378  
800.582.6480 / 952.894.6280  
877.894.6918 / 952.894.6918  
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands  
+31 (0)40 2668620  
+31 (0)40 2668615  
Asia Pacific  
A
Room 24F, Block D, Lily YinDu International Building  
LuoGang, BuJi Town, Shenzhen, CHINA.  
8803-000010 RevA  
©2007 Chief Manufacturing  
11/07  
P
F
+86-755-8996 9226  
+86-755-8996 9217  
 

Bionaire Humidifier BWM8305 User Manual
Black Box Network Router CSU DSU User Manual
Bowers Wilkins Speaker CWM7 User Manual
Briggs Stratton Pressure Washer 020215 User Manual
Campbell Manufacturing Remote Starter 10164 L User Manual
Carrier Furnace 58VCA User Manual
Casio Clock MA0302 A User Manual
Casio Watch MA0811 EA User Manual
Cateye Indoor Furnishings HL 330 User Manual
Chevrolet Offroad Vehicle colbat User Manual