Chief Manufacturing Indoor Furnishings RPMA1 User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Security SLM Series Mount  
RPMA1, -B1, -C1  
 
Installation Instructions  
RPMA1, -B1, -C1  
LEGEND  
Tighten Fastener  
Pencil Mark  
Apretar elemento de fijación  
Befestigungsteil festziehen  
Apertar fixador  
Marcar con lápiz  
Stiftmarkierung  
Marcar com lápis  
Segno a matita  
Serrare il fissaggio  
Bevestiging vastdraaien  
Serrez les fixations  
Potloodmerkteken  
Marquage au crayon  
Loosen Fastener  
Drill Hole  
Aflojar elemento de fijación  
Befestigungsteil lösen  
Desapertar fixador  
Perforar  
Bohrloch  
Fazer furo  
Praticare un foro  
Gat boren  
Allentare il fissaggio  
Bevestiging losdraaien  
Desserrez les fixations  
Percez un trou  
Phillips Screwdriver  
Adjust  
Destornillador Phillips  
Ajustar  
Kreuzschlitzschraubendreher  
Chave de fendas Phillips  
Cacciavite a stella  
Einstellen  
Ajustar  
Regolare  
Afstellen  
Ajuster  
Kruiskopschroevendraaier  
Tournevis à pointe cruciforme  
Open-Ended Wrench  
Llave de boca  
Remove  
Quitar  
Gabelschlüssel  
Chave de bocas  
Chiave a punte aperte  
Steeksleutel  
Entfernen  
Remover  
Rimuovere  
Verwijderen  
Retirez  
Clé à fourche  
By Hand  
Optional  
Opcional  
Optional  
Opcional  
Opzionale  
Optie  
A mano  
Von Hand  
Com a mão  
A mano  
Met de hand  
À la main  
En option  
Hex-Head Wrench  
Security Wrench  
Llave de cabeza hexagonal  
Sechskantschlüssel  
Chave de cabeça sextavada  
Chiave esagonale  
Llave de seguridad  
Sicherheitsschlüssel  
Chave de segurança  
Chiave di sicurezza  
Veiligheidssleutel  
Clé de sécurité  
Zeskantsleutel  
Clé à tête hexagonale  
3
 
RPMA1, -B1, -C1  
Installation Instructions  
TOOLS REQUIRED FOR INSTALLATION  
5/32"  
(Provided)  
PARTS  
Q (1)  
S (1)  
5/32"  
T (8)  
U (4)  
V (4)  
R (4)  
A (4)  
10-24 x 1/4"  
(NOT USED)  
D (4)  
M5 x 12mm  
G (4)  
M2.5 x 10mm  
K (4)  
M5 x 12mm  
M (4)  
M4  
B (4)  
M3 x 10mm  
H (4)  
M3 x 10mm  
N (4)  
M6  
E (4)  
M6 x 12mm  
L (4)  
M6 x 12mm  
C (4)  
M4 x 10mm  
F (4)  
1/4-20 x 1/2"  
J (4)  
M4 x 10mm  
P (4)  
O (1)  
3/32"  
4
 
Installation Instructions  
RPMA1, -B1, -C1  
6. Pull RPMA1 bottom away from RPMA1 top.  
ASSEMBLY AND INSTALLATION  
Attaching Projector Security Legs  
Installing Ceiling Plate and Disassembling  
RPMA1  
1. Attach the projector security legs (R) to the projector, using  
the correct size screws and washers for your specific  
projector. (See Figure 3)  
WARNING: IMPROPER INSTALLATION CAN RESULT IN  
SERIOUS PERSONAL INJURY OR DAMAGE TO  
EQUIPMENT! Structural members MUST be capable of  
supporting five times the combined weight of all equipment  
being mounted.  
x 4  
1. Install ceiling plate and extension accessories following  
installation instruction provided by manufacturer.  
2. Insert key into lock and turn to unlock the projector from  
RPM head. (See Figure 1)  
(M) or (N) x 4  
3. Moving locking lever to "Unlocked" position. (See Figure 1)  
4. Remove the RPM head from RPMA1 top. (See Figure 1)  
(R) x 4  
x
Projector  
4
Figure 3  
2. Add washers (U) to the projector security legs (R). Add  
spacers (T) as necessary to level the projector security legs  
(R). (See Figure 4)  
2
3
2
Figure 1  
(U) x 4  
5. Remove and keep four Phillips screws from top of RPMA1.  
(See Figure 2)  
(T) x 4  
x 4  
5
Figure 4  
Attaching Projector to RPMA1 Bottom  
1. Align projector and RPMA1 bottom so that the projector is  
oriented correctly.  
Figure 2  
5
 
RPMA1, -B1, -C1  
Installation Instructions  
2. Remove the paper backing from the adhesive washers (V)  
and attach projector to RPMA1 bottom using adhesive  
washers (V) and thumbnuts (P) over the security legs (R).  
(See Figure 5)  
(P) x 4  
(V) x 4  
4
RPMA1  
Bottom  
Security  
Legs (R)  
5
Projector  
Figure 7  
Attachment areas if using an  
optional SLB bracket.  
4. Move locking lever to "Locked" position. (See Figure 7)  
5. Insert key into lock and turn to secure projector to mount.  
(See Figure 7)  
Figure 5  
Attaching RPMA1 to Threaded Pipe  
NOTE: An optional SLB bracket may be purchased and used  
to attach projector to RPMA1. (See Figure 5)  
3. Attach RPMA1 bottom to RPMA1 top using four Phillips  
screws removed in Step 5 of Installing Ceiling Plate and  
Disassembling RPMA1. (See Figure 6)  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
PROJECTOR FALLING RESULTING IN SERIOUS  
PERSONAL INJURY OR DAMAGE TO EQUIPMENT. DO  
NOT substitute hardware. Use only the hardware provided by  
the manufacturer.  
3
x 4  
1. Align RPMA1 with end of NTP pipe. (See Figure 8)  
2. Thread RPMA1 up onto pipe by turning counterclockwise  
until hand tight. (See Figure 8)  
2
1
Figure 6  
Figure 8  
6
 
Installation Instructions  
RPMA1, -B1, -C1  
3. Tighten YAW adjustment locking screw using a #2 Phillips  
screwdriver.  
Rough Alignment of RPMA1  
1. Turn RPMA1 clockwise or counterclockwise until the front of  
the RPMA1 and projector is facing target. (See Figure 9)  
PITCH Adjustment  
1. Loosen PITCH adjustment locking screw using a #2 Phillips  
screwdriver. (See Figure 11)  
1
2. Turn PITCH micro-adjustment screw right or left using a #2  
Phillips screwdriver until image is properly aligned on target.  
3. Tighten PITCH adjustment locking screw using a #2 Phillips  
screwdriver.  
2
1
2
Secure set screw,  
then Phillips screw  
from under set screw.  
3
Figure 9  
2. Secure set screw and security Phillips screw under set  
screw. (See Figure 9)  
Adjustments  
The RPMA1 can be adjusted for rotation (yaw), vertical  
elevation (pitch), and horizontal tilt (roll).  
Figure 11  
ROLL Adjustment  
1. Loosen ROLL adjustment locking screw using a #2 Phillips  
screwdriver. (See Figure 12)  
2. Turn ROLL micro-adjustment screw right or left using a #2  
Phillips screwdriver until image is properly aligned on target.  
3. Tighten ROLL adjustment locking screw using a #2 Phillips  
screwdriver.  
1
3
2
1
3
Figure 10  
YAW Adjustment  
2
1. Loosen YAW adjustment locking screw using a #2 Phillips  
screwdriver. (See Figure 10)  
2. Turn YAW micro-adjustment screw right or left using a #2  
Phillips screwdriver until image is properly aligned on target.  
Figure 12  
7
 
RPMA1, -B1, -C1  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378  
800.582.6480 / 952.894.6280  
877.894.6918 / 952.894.6918  
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands  
+31 (0)40 2668620  
+31 (0)40 2668615  
Asia Pacific  
A
Room 30I, Block D, Lily YinDu International Building  
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112  
8802-000254  
¤2007 Chief Manufacturing  
04/07  
P
F
+86-755-8996 9226 ; 8996 9236 ; 8996 9220  
+86-755-8996 9217  
 

Black Box Network Router MT850A User Manual
Black Decker Blender BLM7600G User Manual
Black Decker Iron AS390 User Manual
Blomberg Washer WNF 8427 ACE 40 User Manual
Bosch Appliances Smoke Alarm FPA 1000 UL User Manual
Bosch Power Tools Saw 1671 User Manual
Braun Electric Shaver 340s 4 User Manual
Canon Photo Printer CDI E370 010 User Manual
Casio PDAs Smartphones E 115 User Manual
Char Broil Charcoal Grill 463271108 User Manual