Chief Manufacturing Indoor Furnishings PST 2000 Series User Manual

I N S T A LL A T I O N IN S T R U C T IO N S  
LARGE FLAT PANEL DISPLAY STATIC MOUNT  
PST 2000 Series  
The PST static wall mount accommodates large flat  
screens weighing up to 200 lbs (90.72kg). The teardrop  
holes in the mount allow for quick connect/disconnect of  
the screen, thus simplifying installation and maintenance  
processes.  
The top and bottom mounting brackets are adaptable to  
supporting framework with wood studs that are 16” on  
center or 24”on center.  
The mount has integrated lateral shift, allowing for four  
different mounting options. For dual wood studs 16” on  
center, the lateral shift is + 4.5 inches. For dual wood  
studs 24” on center, the lateral shift is + 0.5 inches.  
After installing the flat screen on the mount, the screen  
can be locked in place using the convenient locking flag.  
A padlock can be used on the latching flag for added  
security.  
The mount is concealed behind the display, making it a  
low profile wall mount.  
! IMPORTANT: If the installation of this product  
requires OSHPD seismic approval, refer to OSHPD  
pre-approval documents and drawings before beginning  
installation. OSHPD documents and drawings are  
available at www.chiefmfg.com, and located on the  
PST 2000 Series  
product information page for the mount.  
BEFORE YOU BEGIN  
x
CAUTION: To prevent damage to the mount, which could affect or void the Factory warranty, thoroughly  
study all instructions and illustrations before you begin to install the mount brackets. Pay particular atten-  
tion to the “Important Warnings and Cautions” on Page 2.  
x
x
The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the  
mount must be capable of supporting five times the total weight of the equipment.  
The maximum weight to be installed on the PST mount is 200 lbs (90.72kg).  
Chief Manufacturing, a division of Milestone AV Technologies  
8804-000255 Rev F  
8401 Eagle Creek Parkway, Savage, MN 55378 ©2008 Milestone AV Technologies  
P: 800.582.6480 / 952.894.6280 F: 877.894.6918 / 952.894.6918  
10/08  
 
Installation Instructions  
PST 2000 Series  
PARTS LIST  
Prior to assembly, unpack the carton completely. Verify  
contents listed in Table 1 and Figure 1.  
CONTENTS  
DIMENSIONAL DRAWING ..................................... 2  
TOOLS REQUIRED FOR INSTALLATION.............. 3  
PARTS LIST .............................................................. 3  
PST INSTALLATION................................................ 4  
Select Mounting Location........................................ 4  
Flag Extender Installation (OPTIONAL).................. 4  
Mount the PST ........................................................ 5  
ATTACH PSB TO THE DISPLAY............................. 6  
INSTALL THE DISPLAY.......................................... 6  
REMOVE THE DISPLAY.......................................... 6  
Read installation instructions completely. If you are  
missing any of the listed parts, contact Customer Service  
at: 1-800/582-6480.  
Table 1. Parts List  
REF DESCRIPTION  
QTY  
10  
20  
30  
40  
50  
60  
Plasma Static Mount  
1
2
2
2
4
4
Flag Extender  
Phillips Machine Screw, 10-24 x ½”  
Thin Nylock Nut, 10-24  
Lag Bolts, 5/16” x 2-½”  
Flat Washer, 5/16”  
TOOLS REQUIRED FOR  
INSTALLATION  
x
x
x
Drill and drill bit set  
Socket wrench set  
30  
#2 Phillips Screwdriver  
NOTE: Other tools may be required depending on your  
method of installation.  
20  
10  
40  
4 Lag Bolts  
50  
4 Washers  
60  
Figure 1. Parts  
3
 
Installation Instructions  
PST 2000 Series  
PST INSTALLATION  
Perform the following procedures to mount the PST.  
Hang the mount on  
the wall temporarily  
using a nail in the  
center hole. Level the  
mount before drilling  
pilot holes.  
Select Mounting Location  
To select the mounting location, do the following:  
WARNING: It is the responsibility of the installer to  
verify that the wall to which the mount is  
anchored will safely support the  
combined load of all attached  
components and equipment.  
Figure 2. Use Triangular Hole to Hang the Mount  
1. Determine the exact mounting location to install the  
wall mount prior to installation, keeping in mind the  
screen size.  
Wood Studs  
16” or 24”  
NOTE: Mount the PST on dual wall studs or some other  
equivalent supporting framework that is vertical  
or horizontal.  
Wall  
Pilot Holes  
2. Using a stud sensor, locate the two wood studs where  
you will mount the PST. Refer to Figure 3 for dual  
wood studs that are 16” or 24” apart on center.  
3. Using a nail as a temporary hook, hang the mount on  
the wall using the triangular hole located in the center  
of the mount (see Figure 2).  
Pilot Holes  
4. Use a pencil to mark the mounting holes where the  
four pilot holes will be drilled into the center of the  
wood stud. Make sure the mounting holes are square  
and straight. Remove the mount from the wall,  
placing it on the floor or a table.  
Figure 3. Wood Studs 16” or 24”Apart on Center  
5. Drill the pilot holes using a 7/32” drill bit.  
Flag Extender Installation (OPTIONAL)  
To install the optional flag extenders, perform the  
following (Refer to Figure 4):  
1. Insert extender (20) slot into top of latching flag.  
2. Install screw (30) through latching flag and extender  
(20) into nut (40).  
3. Repeat for opposite side.  
Figure 4. Optional Flag Extenders  
4
 
Installation Instructions  
PST 2000 Series  
PST INSTALLATION (Cont’d)  
Mount the PST  
To mount the PST, do the following:  
1. Holding the PST against the wall, select the pair of  
mounting holes that best suits your situation (see  
Figures 5, 6, and 7).  
Option A  
NOTE: The mounting holes are slotted to allow for a  
small degree of lateral movement. The mount can  
be centered, or shifted to the left of center, or  
right of center depending on stud location.  
2. Depending on your situation, install the lag bolts (50)  
and washers (60) into the pilot holes previously  
drilled, as described below.  
Figure 5. Mounting Holes – 16” Apart on Center  
(Option A)  
x
x
x
Option A. Install four 5/16” x 2-½” lag bolts  
(50) and four 5/16” washers (60) (two top and  
two bottom) into the mounting holes, centering  
the PST on dual wood studs 16” apart on center  
as shown in Figure 5.  
Option B  
Option C  
OR  
Option B. Install four 5/16” x 2-½” lag bolts (50)  
and four 5/16” washers (60) (two top and two  
bottom) into the mounting holes that are right of  
center on dual wood studs 16” apart as shown in  
Figure 6.  
OR  
Option C. Install four 5/16” x 2-½” lag bolts  
(50) and four 5/16” washers (60) (two top and  
two bottom) into the mounting holes that are left  
of center on dual wood studs 16” apart dual  
wood studs 16” apart on center as shown in  
Figure 6.  
Figure 6. Mounting Holes – 16" Apart on Center  
(Options B and C)  
OR  
x
Option D. Install four 5/16” x 2-½” lag bolts  
(50) and four 5/16” washers (60) (two top and  
two bottom) into the mounting holes, centering  
the PST on dual wood studs 24” apart on center  
as shown in Figure 7.  
Option D  
3. Tighten all lag bolts.  
Figure 7. Mounting Holes – 24" Apart On Center  
(Option D)  
5
 
Installation Instructions  
PST 2000 Series  
ATTACH PSB TO THE DISPLAY  
To attach the PSB to the display, do the following:  
x
To help your identify the correct PSB that  
matches the model number of your display, refer  
to the cross-reference chart at  
x
To download the corresponding PSB installation  
instructions, refer to www.chiefmfg.com.  
INSTALL THE DISPLAY  
To install the display, do the following:  
To install display, align  
NOTE: Verify that all power/audio/video cables are  
disconnected from the display and the latching  
flag is lowered in the down position before  
attempting to mount the display.  
the mounting buttons on  
the PSB with teardrop  
slots on the mount.  
1. With the aid of another person, lift the display up to  
the mount (10) on the wall, aligning mounting  
buttons on the PSB with the teardrop slots on the  
mount, and lower the display firmly into place  
(Figure 8).  
Figure 8. Mount Plasma Static Bracket to Wall  
2. Raise the latching flag (2 places) to secure the display  
(see Figure 9). If the flag does not fully engage,  
check to ensure the mounting buttons are fully seated  
in the slots.  
Raise  
NOTE: A padlock may be installed through the hole in  
latching  
flag to  
lock  
the latching flag for additional security.  
display  
REMOVE THE DISPLAY  
To remove the display from the mount, do the following:  
1. Disconnect all power/audio/video cables.  
Figure 9. Raise Latching Flag to Lock  
2. Lower the latching flag to unlock the display  
(see Figure 10).  
3. With the aid of another person, lift the display up and  
out of the teardrop slots in the mount to remove the  
display.  
Lower  
latching  
flag to  
unlock  
display  
Figure 10. Lower Latching Flag to Unlock  
6
 
Installation Instructions  
PST 2000 Series  
7
 
Installation Instructions  
PST 2000 Series  
8
 

Black Box Power Supply 20 Amp Horizontal PDU, 14 Outlet 5 20R User Manual
Bogen Stereo Amplifier V250 User Manual
Boss Audio Systems Musical Instrument OC 20G User Manual
Bradley Smoker Plumbing Product MG 2 BIR3 User Manual
Britax Car Seat Boulevard User Manual
Brother Printer 5250DN User Manual
Califone MP3 Player 2385 03 User Manual
Canon Camcorder 540EZ User Manual
Carson Speaker CSP 100B User Manual
Chicago Electric Sander 93431 User Manual