Chief Manufacturing Indoor Furnishings PDC Series User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Plasma Dual Ceiling Mount  
PDC Series  
 
Installation Instructions  
PDC Series  
LEGEND  
Tighten Fastener  
Pencil Mark  
Apretar elemento de fijación  
Befestigungsteil festziehen  
Apertar fixador  
Marcar con lápiz  
Stiftmarkierung  
Marcar com lápis  
Segno a matita  
Potloodmerkteken  
Marquage au crayon  
Serrare il fissaggio  
Bevestiging vastdraaien  
Serrez les fixations  
Loosen Fastener  
Drill Hole  
Aflojar elemento de fijación  
Befestigungsteil lösen  
Desapertar fixador  
Perforar  
Bohrloch  
Fazer furo  
Praticare un foro  
Gat boren  
Allentare il fissaggio  
Bevestiging losdraaien  
Desserrez les fixations  
Percez un trou  
Phillips Screwdriver  
Adjust  
Destornillador Phillips  
Ajustar  
Kreuzschlitzschraubendreher  
Chave de fendas Phillips  
Cacciavite a stella  
Einstellen  
Ajustar  
Regolare  
Afstellen  
Ajuster  
Kruiskopschroevendraaier  
Tournevis à pointe cruciforme  
Open-Ended Wrench  
Llave de boca  
Remove  
Quitar  
Gabelschlüssel  
Chave de bocas  
Chiave a punte aperte  
Steeksleutel  
Entfernen  
Remover  
Rimuovere  
Verwijderen  
Retirez  
Clé à fourche  
By Hand  
Optional  
Opcional  
Optional  
Opcional  
Opzionale  
Optie  
A mano  
Von Hand  
Com a mão  
A mano  
Met de hand  
À la main  
En option  
Hex-Head Wrench  
Security Wrench  
Llave de cabeza hexagonal  
Sechskantschlüssel  
Chave de cabeça sextavada  
Chiave esagonale  
Llave de seguridad  
Sicherheitsschlüssel  
Chave de segurança  
Chiave di sicurezza  
Veiligheidssleutel  
Clé de sécurité  
Zeskantsleutel  
Clé à tête hexagonale  
3
 
PDC Series  
Installation Instructions  
TOOLS REQUIRED FOR INSTALLATION  
9/16" (14.3 mm)  
PARTS  
A (1)  
C (1)  
5/32"  
B (1)  
1/8"  
D (2)  
D3 (1)  
10-24 x 3/8"  
D2 (1)  
10-24  
D4 (1)  
3/16"  
D6 (1)  
4-40  
D5 (1)  
4-40 x 2-1/2"  
D1 (1)  
D8 (1)  
5/16-18 x 2-3/4"  
D7 (1)  
5/16-18  
4
 
Installation Instructions  
PDC Series  
4. Attach interface brackets to back of displays following  
INSTALLATION  
instructions included with the interface brackets.  
Preparing for Installation  
Installing Displays on PDC  
1. Attach click-lock flag kits (D) to PDC following instructions  
included with the kits.  
WARNING: EXCEEDING MAXIMUM WEIGHT CAPACITY  
CAN LEAD TO SERIOUS PERSONAL INJURY OR  
DAMAGE TO EQUIPMENT! It is the installers responsibility  
to ensure the total amount of weight placed on the mount  
does not exceed 400 lbs (181.44 kg) [200 lbs (90.72 kg) each  
faceplate].  
WARNING: FAILURE TO PROVIDE ADEQUATE  
STRUCTURAL STRENGTH FOR THIS COMPONENT CAN  
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE  
TO EQUIPMENT! It is the installer’s responsibility to make  
sure the structure to which this component is attached can  
support five times the combined weight of all equipment.  
Reinforce the structure as required before installing the  
component.  
WARNING: DISPLAY MAY WEIGH IN EXCESS OF  
40 LBS (18.14 KG)! Always use two people and proper lifting  
techniques when installing or positioning display.  
2. Determine if NPT pipe is 1-1/2" or 2".  
If NPT pipe is 1-1/2", proceed to Step 3.  
If NPT pipe is 2", loosen set screw and  
remove the 1-1/2" to 2" pipe coupler, then  
proceed to Step 3.(See Figure 1)  
Pipe  
Coupler  
Set  
Screw  
(A)  
Display  
Figure 3  
1. While supporting each side of display, align four mounting  
buttons on display or interface bracket with four slots on  
PDC. (See Figure 3)  
2. Lower each display into place listening for audible "click" to  
ensure recessed area of mounting buttons are properly  
seated in lower area of mounting holes.(See Figure 4)  
Figure 1  
3. Thread the PDC (A) onto the NPT pipe extension and  
tighten set screw. (See Figure 2)  
NPT  
Pipe  
Set  
Screw  
1
(A)  
Figure 2  
5
 
PDC Series  
Installation Instructions  
Remove bolt  
or padlock  
if used  
2
3
May remove  
pin and nut and  
move to lower holes  
1
Pin in  
"Closed"  
position -  
move to  
"Open"  
2
position to  
remove  
display  
A padlock or bolt  
may be placed  
through latch holes  
5
Figure 4  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
DISPLAY FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Ensure mounting  
buttons are completely engaged in mounting holes.  
Pin in  
"Open"  
position -  
move to  
"Closed"  
position  
NOTE: Holes are provided in the faceplate for use with a  
padlock or similar locking device, if desired. In addition,  
the pin and nut may be removed from the upper holes  
and moved to the lower holes for use as a more  
permanent locking device. (See Figure 4)  
after display  
is removed.  
3. Connect and secure power, audio and video cables.  
Removing Displays from PDC  
Figure 5  
1. Disconnect all power/audio/video cables.  
2. Remove bolt or padlock from faceplate (if used).  
(See Figure 5)  
WARNING: EACH DISPLAY MAY WEIGH IN EXCESS OF  
40 LBS EACH! Always use two people and proper lifting  
techniques when installing or positioning displays on PDC.  
NOTE: The pin may have been used as a more permanent  
locking device. If so, remove nut and pin and move  
from the lower holes to the upper holes.  
4. Carefully lift displays from PDC.  
3. Pull back on flag on upper mounting hole and press pin  
down down into "Open" position. (See Figure 5)  
5. Lift up on pin and place flag back against faceplate to return  
it to "Closed" position. (See Figure 5)  
Adjustments  
Roll Adjustment  
1. Loosen two Nylock nuts inside the PDC. (See Figure 6)  
2. Using the slotted holes, adjust the roll, or horizontal  
movement.  
3. Tighten two Nylock nuts.  
6
 
Installation Instructions  
PDC Series  
4
5
x 2  
x 2  
x 2  
x 2  
1
2
6
3
(Display and faceplate  
removed for clarity)  
Figure 6  
Pitch Adjustment  
4. Loosen two screws on side of PDC. (See Figure 6)  
5. Adjust to desired pitch, or vertical movement.  
6. Tighten the screws on side of PDC.  
7
 
PDC Series  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378  
800.582.6480 / 952.894.6280  
877.894.6918 / 952.894.6918  
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands  
+31 (0)40 2668620  
+31 (0)40 2668615  
Asia Pacific  
A
Room 24F, Block D, Lily YinDu International Building  
LuoGang, BuJi Town, Shenzhen, CHINA.  
8805-000115 Rev.D  
¤2008 Chief Manufacturing  
01/08  
P
F
+86-755-8996 9226  
+86-755-8996 9217  
 

Black Box Network Hardware ACU3001A User Manual
Black Decker Bread Maker BMH110 User Manual
Black Decker Food Processor FX710 B5 User Manual
Blomberg Freezer FSE1630u User Manual
Bosch Appliances Dishwasher SHP65TL5UC User Manual
Bosch Appliances Webcam EX36 IP User Manual
Bostitch Staple Gun CR1000E User Manual
Briggs Stratton Plumbing Product 117400 User Manual
CDA Ventilation Hood 3Q9 User Manual
Chamberlain Washer Dryer 953CB User Manual