Chief Manufacturing Indoor Furnishings LCD2TS User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Multiple Projector Stacking System - Table Stand  
LCD2TS  
 
Installation Instructions  
LCD2TS  
LEGEND  
Tighten Fastener  
Pencil Mark  
Apretar elemento de fijación  
Befestigungsteil festziehen  
Apertar fixador  
Marcar con lápiz  
Stiftmarkierung  
Marcar com lápis  
Segno a matita  
Potloodmerkteken  
Marquage au crayon  
Serrare il fissaggio  
Bevestiging vastdraaien  
Serrez les fixations  
Loosen Fastener  
Drill Hole  
Aflojar elemento de fijación  
Befestigungsteil lösen  
Desapertar fixador  
Perforar  
Bohrloch  
Fazer furo  
Praticare un foro  
Gat boren  
Allentare il fissaggio  
Bevestiging losdraaien  
Desserrez les fixations  
Percez un trou  
Phillips Screwdriver  
Adjust  
Destornillador Phillips  
Ajustar  
Kreuzschlitzschraubendreher  
Chave de fendas Phillips  
Cacciavite a stella  
Einstellen  
Ajustar  
Regolare  
Afstellen  
Ajuster  
Kruiskopschroevendraaier  
Tournevis à pointe cruciforme  
Open-Ended Wrench  
Llave de boca  
Remove  
Quitar  
Gabelschlüssel  
Chave de bocas  
Chiave a punte aperte  
Steeksleutel  
Entfernen  
Remover  
Rimuovere  
Verwijderen  
Retirez  
Clé à fourche  
By Hand  
Optional  
Opcional  
Optional  
Opcional  
Opzionale  
Optie  
A mano  
Von Hand  
Com a mão  
A mano  
Met de hand  
À la main  
En option  
Hex-Head Wrench  
Security Wrench  
Llave de cabeza hexagonal  
Sechskantschlüssel  
Chave de cabeça sextavada  
Chiave esagonale  
Llave de seguridad  
Sicherheitsschlüssel  
Chave de segurança  
Chiave di sicurezza  
Veiligheidssleutel  
Clé de sécurité  
Zeskantsleutel  
Clé à tête hexagonale  
3
 
LCD2TS  
Installation Instructions  
TOOLS REQUIRED FOR INSTALLATION  
7/32" (5.5mm)  
#2  
1/2" (12.7mm)  
PARTS  
C (1)  
A (2)  
B (1)  
D (4)  
E(1)  
F (1)  
G (8)  
I (5)  
5/16-18X3/8"  
J (8)  
1/4-20X1-1/4"  
K (8)  
1/4-20X1-1/2"  
H (8)  
1/4-20 x 1-1/2"  
L (16)  
M (8)  
4
 
Installation Instructions  
LCD2TS  
Assembly And Installation  
For RPA Models Only  
6
(F)  
WARNING: Failure to provide adequate structural strength  
for this component can result in serious personal injury or  
damage to equipment. It is the installer’s responsibility to  
make sure the structure to which this component is attached  
can support five times the combined weight of all equipment.  
Reinforce the structure as required before installing the  
component.  
(C)  
1. Set the base plate (B) on a flat stable work surface and  
adjust the feet as necessary.  
(I)x2  
5
2. Thread the 1-1/2" pipe section (C) into the base plate and  
tighten.  
3. Secure NPT pipe to base plate using one 5/16-18 x 3/8" set  
screw (I).  
4. Attach RPA to projector arm (A) using four 1/4-20 X 1-1/2"  
carriage bolts (H), four 1/4-20 acorn nuts (G) and 1/4" flat  
washers (L). (See Figure 1)  
Figure 2  
10. Adjust projector for correct registration.  
For RPM Models Only  
1. Proceed with Steps 1-3 under For RPA Models Only.  
2. Place RPM on its top so that four screw holes are visible  
through the square in the RPM base. (See Figure 3)  
(C)  
(A)  
(G)x4  
4
3. Insert four 1/4"-20x1-1/2" (K) button head cap screws into  
the bottom of the RPM. (See Figure 3)  
(L)x4  
NOTE: The RPM base is not shown in Figure 3 for clarity only.  
It should NOT be removed for this installation process.  
RPA  
(D)  
4 screw  
holes  
2
Adjustable  
Feet  
RPM  
(H)x4  
(M)x4  
Figure 1  
RPM base not  
shown for  
clarity only.  
5. Slide both projector arms (A) onto the 1-1/2" vertical pipe  
section (C) and secure using two 5/16-18 x 3/8" set screws  
(I) on each arm. (See Figure 2)  
(K)x4  
6. Thread 1-1/2" safety nut (F) onto threaded end of the 1-1/2"  
pipe section. (See Figure 2)  
Figure 3  
7. Mount projector hanging bracket to your projector (see RPA  
instructions).  
4. Place four nylon spacers (M) onto the screws as shown in  
Figure 3.  
8. Partially thread 10-24 thumbscrews onto 10-24 studs at top  
of hanger bracket plate. The quantity of thumbscrews may  
vary from three to six.  
5. Tighten the screws through the nylon spacers and into the  
two interface brackets (D). (See Figure 3)  
9. Align studs with key slots of RPA, slide RPA into place, and  
secure RPA by tightening thumbscrews.  
5
 
LCD2TS  
Installation Instructions  
6. Insert four 1/4"-20x1-1/4" (J) button head cap screws from  
the top of the projector arm. (See Figure 4)  
(A)  
(J)x4  
8
(L)x4  
RPM not shown  
for clarity only  
Figure 4  
7. Place a 1/4" flat washer (L) onto each screw.  
8. Hold the RPM (with interface brackets attached) to the  
bottom of the projector arm and tighten the screws through  
the washers and into the interface brackets.  
9. Proceed with Steps 5 - 10 from For RPA Models Only  
section  
6
 
Installation Instructions  
LCD2TS  
7
 
LCD2TS  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378  
800.582.6480 / 952.894.6280  
877.894.6918 / 952.894.6918  
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands  
+31 (0)40 2668620  
+31 (0)40 2668615  
Asia Pacific  
A
Room 30I, Block D, Lily YinDu International Building  
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112  
8804-000053 RevA  
¤2006 Chief Manufacturing  
11/06  
P
F
+86-755-8996 9226 ; 8996 9236 ; 8996 9220  
+86-755-8996 9217  
 

Bissell Vacuum Cleaner 13H8 User Manual
Blanco Indoor Furnishings 157 011 User Manual
Blanco Indoor Furnishings 157 067 User Manual
Blue Rhino Charcoal Grill CBT802WB User Manual
Bodum Coffee Grinder 10713 User Manual
Bosch Appliances Boiler 14 19CBI User Manual
Breville Juicer JE900 User Manual
BRK electronic Carbon Monoxide Alarm RM4 User Manual
BUSH Flat Panel Television IDLED2202DVD User Manual
Casio Watch 2263 1 User Manual