Chief Manufacturing Indoor Furnishings KTP Series User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Horizontal And Vertical Table Stands  
and Accessories  
Model: KTP-Series  
The KTP-Series is a free standing, pole mount solution for multiple displays.  
KTP-320  
KTP-220 / KTP-225  
KTP-440 / KTP-445  
KTP-230  
BEFORE YOU BEGIN  
CAUTION!  
To prevent damage to the Kit, which could affect or void the Factory warranty, and to the equipment that will be  
attached to it, thoroughly study all instructions and illustrations before you begin the installation.  
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480.  
Chief® and Centris™ are trademarks of Milestone AV Technologies. All rights reserved.  
8832-000142 Rev I  
¤2008 Milestone AV Technologies,  
a Duchossois Group Company  
Chief Manufacturing, a products division of  
Milestone AV Technologies  
8401 Eagle Creek Parkway, Savage, MN 55378  
P: 800.582.6480 / 952.894.6280  
11/08  
 
Installation Instructions  
Model: KTP-Series  
(160)  
(10 Includes 210, 220, 230)  
(180)  
(200)  
(120)  
(190)  
(170)  
(20)  
(130)  
(140)  
250  
260  
(30)  
(110)  
(100)  
(40)  
240  
(80)  
(90)  
(50)  
(70)  
(60)  
Figure 1: Parts  
ASSEMBLY AND INSTALLATION  
(210)  
(60)  
Mount Assembly  
KTP-230 Assembly  
To assemble the KTP-230:  
(220)  
1. Assemble pole (60) to base (40) using one 3/8-16 x 1"  
FHCS (90). (see Figure 2)  
(60)  
(230)  
(140)  
Figure 3: Mount Centris Head with Pole Clamp  
(90)  
(40)  
Figure 2: Assemble Pole to Base  
2. Place front pole clamp, with Centris Head, (210)  
against pole in approximate mounting location.  
3. Place three BHCS (230) into rear pole clamp (220)  
and place against pole aligning with front pole clamp  
(210). (see Figure 3)  
3
 
Model: KTP-Series  
Installation Instructions  
NOTE: Equally tighten screws (230) against front pole  
mount (210) and rear (220) pole clamps.  
(see Figure 4)  
Display Installation  
Attach Centris Head to Flush Mount Display  
CAUTION!  
CAUTION: If display uses a screw size other than  
those included in the kit, DO NOT use the screws  
provided. Using the wrong screws could result in  
damage to your monitor.  
(230)  
Keep equal  
distance between  
mount and  
clamp when  
tightening  
(220)  
1. Install two M4 x 12mm Phillips pan head screws (160)  
into two upper mounting holes in display back.  
(see Figure 6)  
NOTE: DO NOT fully tighten at this time.  
(210)  
2. Hang display on Centris head. (see Figure 7)  
Figure 4:  
3. Install bottom two M4 x 12mm Phillips pan head  
screws (160) through Centris head mounting holes  
and into lower mounting holes in display back.  
4. Secure rear pole clamp (220) to front pole mount  
(210) and pole by tightening three BHCS (230) using  
5/32" hex key (120). (see Figure 3)  
4. Tighten ALL four M4 x 12mm Phillips pan head  
screws (160). (see Figure 8)  
KTP-220, 320, and 440 Assembly  
To assemble the KTP-220, 320, and 440:  
M4 x 12mm Phillips Pan Head Screw (30)  
1. Assemble pole (50) to base (40) using one 3/8-16 x 1"  
FHCS (90). (see Figure 2)  
2. Assemble pole clamp back (240) to pole mount front  
using two FW (250) and two BHCS (260) using a  
5/32" hex key. (see Figure 5)  
3. Secure pole mount back (240) to pole mount front and  
pole by tightening two BHCS (260) using a 5/32" hex  
key.  
Display  
Pole  
Pole Mount front  
with Array  
Figure 6: Prepare Display  
(250)  
Display  
(260)  
(20, 30)  
Pole Clamp Back (240)  
Centris Head  
Figure 5: Assemble Array Rail to Pole  
Figure 7: Hang Display  
4
 
Installation Instructions  
Centris Head  
Model: KTP-Series  
3. Place display face down on a clean dry surface.  
Display  
4. Place four 3/8" or 3/4" nylon spacers (190 or 200)  
over four mounting holes in display back (see Figure  
11).  
5. Align Centris head mounting holes with four nylon  
spacers (see Figure 11).  
6. Secure Centris head to display using four  
M4 x 20mm Phillips pan head screws (170), or four  
M4 x 30mm Phillips pan head screws (180)  
(see Figure 11).  
(20, 30)  
(160)  
Phillips Pan Head Screw  
(170 or 180)  
Centris Head  
Figure 8: Secure Display to Centris Bracket  
Attach Centris Head to Recessed Mount Display  
Spacer  
(190 or 200)  
NOTE: Refer to Table 3 to select the applicable screw  
and spacer combination.  
1. Uninstall end lock using the 5/32" hex key (120).  
(see Figure 9)  
2. Remove Centris head from array rail (20, 30).  
Centris Head  
Square Nut  
Display  
Figure 11: Mount Centris Bracket to Display  
7. Slide display with Centris bracket onto array rail (20,  
30) (see Figure 12).  
NOTE: Repeat previous steps for each additional display.  
End Lock  
(20, 30)  
8. Reinstall end locks into mounting rail using the 5/32"  
hex key (120) (see Figure 13).  
Figure 9: Remove End Lock(s)  
Display with Centris Bracket  
(20, 30)  
(20, 30)  
Centris Head  
Figure 10: Slide Centris Bracket off Array Rail  
Figure 12: Mount Display with Centris Bracket to  
Array Rail  
5
 
Model: KTP-Series  
Installation Instructions  
Display Pitch and Roll Adjustment  
To adjust display pitch or roll position:  
(20, 30)  
1. Loosen Centris bracket front adjustment knob.  
(see Figure 15)  
End Lock  
2. Tilt display up or down, or adjust display roll left or  
right until properly positioned.  
3. Tighten Centris bracket front adjustmnent knob.  
Pitch/Roll  
Adjustment  
Knob  
Centris Head  
End Lock Retaining Screw  
Figure 13: Reinstall End Lock(s)  
ADJUSTMENTS  
Display Adjustment  
The KTP Series mount allows horizontal, pitch, and  
rotational adjustment of each display.  
The KTP Series mount also allows a full 360 deg. of  
display rotation with a maximum pitch range of 15° up  
and 15° down.  
Figure 15: Display Pitch and Roll Adjustment  
Display Horizontal Position Adjustment  
CABLE MANAGEMENT  
To adjust display horizontal position:  
The KTP Series mount includes cable management  
features used to properly route and secure display  
cables.  
1. Loosen Centris bracket rear adjustment knob (see  
Figure 14).  
2. Slide Centris bracket with display left or right until  
properly positioned on array rail.  
To use the cable management features:  
1. Connect cables to display.  
3. Tighten Centris bracket rear adjustmnent knob.  
2. Route cables through cable clips on array rail.  
3. Route cables down pole and away from mount and  
secure to pole using sheath (80).  
Horizontal  
Adjustment  
Knob  
Cable Clips  
(80)  
Figure 16: Cable Management  
Figure 14: Display Horizontal Adjustment  
6
 
Installation Instructions  
Model: KTP-Series  
7
 
 

Belkin Microcassette Recorder 25PB082 User Manual
Belkin Power Supply AP51300fc10 BLK User Manual
Black Box Modem SME 4M User Manual
Blue Rhino Charcoal Grill PC2694 2S User Manual
Bodum DVR F1 ACE User Manual
Bogen Speaker System AE 5NC User Manual
Bush Hog Brush Cutter 2615L User Manual
Canon Scanner 4508B002 User Manual
Casio Digital Camera EX S880 User Manual
CFM Corporation Outdoor Fireplace ODSHR42 User Manual