Chief Manufacturing Indoor Furnishings KSG110 User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Universal Slat Wall  
Dual Arm Mounts  
KSG110  
 
Installation Instructions  
KSG110  
LEGEND  
Pencil Mark  
Tighten Fastener  
Marcar con lápiz  
Stiftmarkierung  
Marcar com lápis  
Segno a matita  
Potloodmerkteken  
Marquage au crayon  
Apretar elemento de fijación  
Befestigungsteil festziehen  
Apertar fixador  
Serrare il fissaggio  
Bevestiging vastdraaien  
Serrez les fixations  
Drill Hole  
Loosen Fastener  
Perforar  
Aflojar elemento de fijación  
Befestigungsteil lösen  
Desapertar fixador  
Bohrloch  
Fazer furo  
Praticare un foro  
Gat boren  
Allentare il fissaggio  
Bevestiging losdraaien  
Desserrez les fixations  
Percez un trou  
Adjust  
Phillips Screwdriver  
Ajustar  
Destornillador Phillips  
Einstellen  
Ajustar  
Kreuzschlitzschraubendreher  
Chave de fendas Phillips  
Cacciavite a stella  
Regolare  
Afstellen  
Ajuster  
Kruiskopschroevendraaier  
Tournevis à pointe cruciforme  
Remove  
Quitar  
Open-Ended Wrench  
Llave de boca  
Entfernen  
Remover  
Rimuovere  
Verwijderen  
Retirez  
Gabelschlüssel  
Chave de bocas  
Chiave a punte aperte  
Steeksleutel  
Clé à fourche  
Optional  
Opcional  
Optional  
Opcional  
Opzionale  
Optie  
By Hand  
A mano  
Von Hand  
Com a mão  
A mano  
Met de hand  
À la main  
En option  
Security Wrench  
Hex-Head Wrench  
Llave de seguridad  
Sicherheitsschlüssel  
Chave de segurança  
Chiave di sicurezza  
Veiligheidssleutel  
Clé de sécurité  
Llave de cabeza hexagonal  
Sechskantschlüssel  
Chave de cabeça sextavada  
Chiave esagonale  
Zeskantsleutel  
Clé à tête hexagonale  
3
 
KSG110  
Installation Instructions  
TOOLS REQUIRED FOR INSTALLATION  
3/16"  
5/32"  
(Provided)  
(Provided)  
PARTS  
A (1)  
B (1)  
E (1)  
C (1)  
3/16"  
D (1)  
5/32"  
G1  
G5  
G4  
G2  
F (2)  
8-32 x 3/8"  
G3  
G (1)  
4
 
Installation Instructions  
KSG110  
INSTALLATION  
B
WARNING: FAILURE TO PROVIDE ADEQUATE  
STRUCTURAL STRENGTH FOR THIS COMPONENT CAN  
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE  
TO EQUIPMENT! It is the installer’s responsibility to make  
sure the structure to which this component is attached can  
support five times the combined weight of all equipment.  
Reinforce the structure as required before installing the  
component.  
1. Install the slat wall bracket (B) following the instructions  
included with kit.  
IMPORTANT ! : If the display being installed has a recessed  
mounting surface, the display must be assembled to the mount  
prior to mount installation. See Display Installation in this  
document before proceeding.  
3
A
2. Insert top of mount (A) over lip on top of wall bracket (B).  
(See Figure 1)  
Figure 2  
4. Tighten set screw using 5/32" hex key (D). (See Figure 3)  
CAUTION: IMPROPER INSTALLATION CAN LEAD TO  
DISPLAY FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Make sure set  
screw engages back side of mounting dish on wall bracket  
(B). (See Figure 3)  
A
2
A
B
B
4
Figure 1  
3. Swing mount (A) down flush against wall bracket (B). (See  
Figure 2)  
Figure 3  
DISPLAY INSTALLATION  
The mounting holes on the back of the display will be flush with  
the back surface, or recessed into the back. Refer to the  
applicable installation procedure below.  
Swing Arm Flush Display Installation  
CAUTION: IMPROPER INSTALLATION CAN LEAD TO  
DISPLAY FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Using screws of  
improper size may damage your display! Proper screws will  
easily and completely thread into display mounting holes.  
5
 
KSG110  
Installation Instructions  
CAUTION: IMPROPER INSTALLATION CAN LEAD TO  
DISPLAY FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread  
engagement in display may cause display to fall! Back out  
screws ONLY as necessary to allow installation of Centris  
bracket!  
Centris Cup  
4
1. Ensure Centris cup is able to swivel and tilt easily, yet still  
be tight enough to hold display in desired position. Adjust  
as required before proceeding. See "ADJUSTMENT" for  
detail.  
G1 x 2  
2. Using Phillips screwdriver, carefully install two screws (G1)  
into the upper mounting holes on the display. Thread  
screws completely into display, then back out 3 complete  
turns.  
3. Align two screws (G1) (installed on the back of the display  
in the previous step) with the two top teardrop mounting  
holes on the Centris cup.  
Figure 5  
6. Proceed to "CABLE MANAGEMENT."  
Swing Arm Recessed Display Installation  
CAUTION: IMPROPER INSTALLATION CAN LEAD TO  
DISPLAY FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Smaller area of  
teardrop mounting holes must be facing downward for proper  
installation. Reposition Centris cup if required.  
1. Ensure Centris bracket is able to swivel and tilt easily, yet  
still be tight enough to hold display in desired position.  
Adjust as required before proceeding. See  
"ADJUSTMENT" for detail.  
2. Carefully place display face down on a clean and dry  
surface.  
3. Determine depth of recessed mounting holes relative to  
back surface of display.  
4. Select proper length spacer and screw from table below:  
G1 x 2  
IMPORTANT ! : All spacers used should be the same length.  
If the recess depths result in multiple spacer lengths, then  
2
select the longer spacer.  
IF recess DEPTH is: THEN use spacer:  
3/8" or less G4 (3/8" long)  
AND screw:  
3
G2 (G4 x 20mm)  
G3 (G4 x 30mm)  
More than 3/8" up to G5 (3/4" long)  
and including 3/4"  
5. Place the four (G4 or G5) spacers over each mounting hole  
on the back of display. (See Figure 6)  
6. Orient mount so that mounting holes in the Centris cup are  
aligned with the holes in the spacers (G4 or G5); rotate the  
Centris cup as required (See Figure 6).  
Centris Cup  
Figure 4  
4. Using Phillips screwdriver, install two screws (G1) through  
the lower mounting holes in Centris cup into the display.  
CAUTION: IMPROPER INSTALLATION CAN LEAD TO  
DISPLAY FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Using screws of  
improper size may damage your display! Proper screws will  
easily and completely thread into display mounting holes.  
5. Tighten all screws (G1). Do not overtighten!  
7. Using Phillips screwdriver, install four screws (G2 or G3)  
through the mounting holes in Centris cup, through the  
spacers (G4 or G5), into display (See Figure 6).  
8. Tighten all four screws. Do not overtighten!  
9. Return to mount installation section to continue.  
6
 
Installation Instructions  
Centris Cup  
KSG110  
G2 or G3  
(4 places)  
7
G4 or G5  
(4 places)  
Cable Management  
Bracket (in open position)  
5
Cable Path (typical)  
NOTE: Display not shown for clarity.  
Figure 8  
4. Close cable management bracket by sliding it back towards  
the centerline of the arm (See Figure 7).  
Figure 6  
NOTE: If necessary, cable management bracket attach screws  
may be tightened using hex key.  
Cable Management  
1. Attach all cables to display.  
2. Open the cable management bracket by sliding it towards  
the edge of the arm (See Figure 7).  
CAUTION: Ensure that adequate cable slack exists for  
movement of display, and that cables will not be pinched by  
installation of cover (E) or screws (F).  
NOTE: If necessary, cable management bracket attach screws  
may be loosened using hex key.  
5. Carefully insert cables in cavity located in lower portion of  
mount arm (See Figure 9).  
6. Using Phillips screwdriver, install cover (E) with two  
screws (F).  
Attach  
Screws  
Cable Path  
(typical)  
CLOSED Position  
View from Bottom  
OPEN Position  
Figure 7  
E
CAUTION: Ensure that adequate cable slack exists for  
movement of display, and that cables will not be pinched  
when bracket is closed.  
F x 2  
3. Carefully insert cables into bracket (See Figure 8).  
Figure 9  
Installation is complete.  
Adjustments  
Centris Head Tension Adjustment  
1. If previously attached, disconnect cables from  
display, remove display.  
7
 
KSG110  
Installation Instructions  
2. Using Phillips screwdriver, slightly loosen or tighten  
the adjustment screw as necessary (See Figure 10).  
Adjustment Screw  
2
Figure 10  
3. Reinstall display. See Display Installation in this  
document.  
Display Adjustment  
Lateral position on display:  
Figure 12  
1. Using your fingers, slightly loosen adjustment knob "A".  
(See Figure 11)  
2. Slide display to desired position.  
3. Using your fingers, tighten adjustment knob "A". (See  
Figure 11)  
PITCH / YAW / ROLL Tension  
1. Using your fingers, slightly loosen adjustment knob "B".  
(See Figure 11)  
2. Adjust display as desired.  
3. Using your fingers, tighten adjustment knob "B".  
B
A
Figure 11  
Swing Arm Tension  
1. Using 3/16" hex wrench (C), loosen or tighten adjustment  
screw(s) as necessary (See Figure 12).  
8
 
Installation Instructions  
KSG110  
9
 
KSG110  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378  
800.582.6480 / 952.894.6280  
877.894.6918 / 952.894.6918  
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands  
+31 (0)40 2668620  
+31 (0)40 2668615  
Asia Pacific  
A
Room 30I, Block D, Lily YinDu International Building  
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112  
8832-000237  
¤2007 Chief Manufacturing  
08/07  
P
F
+86-755-8996 9226 ; 8996 9236 ; 8996 9220  
+86-755-8996 9217  
 

Bernard Stereo Receiver Cable Connectors User Manual
Black Box Computer Hardware AC300A RX User Manual
Blaupunkt Car Amplifier PCA450 User Manual
Bravetti Oven TO230H User Manual
Briggs Stratton Portable Generator 30217 User Manual
Brother Sewing Machine BES 941BC User Manual
Campbell Hausfeld Nail Gun JB3495 User Manual
Canon Fax Machine L280 User Manual
Carrier Air Conditioner 38HDF018 036 User Manual
Chromalox Electric Heater GS User Manual