Chief Manufacturing Indoor Furnishings JWDSK User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Instrucciones de instalación  
Installationsanleitung  
Istruzioni di installazione  
Installatie-instructies  
Instruções de Instalação  
Instructions d´installation  
Medium Flat Panel Steel Stud Wall Mount  
Spanish Product Description  
German Product Description  
Portuguese Product Description  
Italian Product Description  
Dutch Product Description  
French Product Description  
JWDSK Series  
 
Installation Instructions  
JWDSK Series  
TOOLS REQUIRED FOR INSTALLATION AND PARTS  
1/2" (Ø13mm)  
(3/16")  
(5/32")  
I/M  
A (1)  
x1  
Interface  
Bracket  
Kit  
C (4)  
8-32 x 3/8"  
B (2)  
(Including Hardware)  
E (4)  
(1/4")  
x 1  
D (4)  
(1/4"-20 x 1-3/4")  
F (4)  
(1/4"-20 SNAP TOGGLE BB)  
G (1)  
3/16"  
3
 
JWDSK Series  
Installation Instructions  
Site Requirements  
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY  
OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto a  
steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific  
instructions before attempting installation. It should also be noted that no other equipment should be mounted to the same stud.  
16" or 24" (on center) Studs  
Display Mount Installation Location  
(Must be centered on stud)  
If back side of wall is unfinished, drywall must be installed  
to a minimum of one stud left and right of the stud(s)  
being used to install the mount. Drywall must be  
secured to studs with screws 12" on center  
There must be a minimum of  
1-7/8" (48mm) clearance  
inside wall  
FRONT  
Drywall  
1/2" minimum  
Drywall Thickness  
(Both Sides of Stud)  
Steel Stud (2 x 4 / 25ga minimum)  
Stud type and structural strength must conform to the North American  
Specification for the Design of Cold-Formed Steel Structural Members.  
[362 S 125 18, C-Shaped, S-Stud Section]  
Figure 1  
4
 
Installation Instructions  
JWDSK Series  
MOUNT INSTALLATION  
After determining the site meets the installation requirements:  
Drywall  
1. Identify desired mounting location on wall.  
2. Using a stud finder or similar method locate studs.  
3. Align mounting holes in mount with studs making sure  
mounting holes are centered on studs. (See Figure 2)  
Plastic Straps  
4. Mark location of three mounting holes on wall.  
5. Drill four 1/2" (Ø13mm) holes. (See Figure 2)  
1/2" (Ø13mm) x4  
(F) x4  
Figure 3  
7. Holding plastic straps on anchor (F), pull anchor away from  
wall until channel rests flush behind wall making sure  
anchor channel is positioned vertically on stud as show in  
figures below. (See Figure 4)  
8. Slide plastic cap on anchor (F) towards wall until flange of  
cap is flush with wall. (See Figure 4)  
Steel Stud  
Drywall  
(A) x1  
Plastic Cap  
(F) x4  
Anchor Metal Channel  
Mounting holes  
centered on  
studs  
SIDE VIEW  
Figure 4  
Figure 2  
9. Snap off plastic straps on anchor at wall by pushing side to  
side, snapping off straps level with flange of plastic cap.  
(See Figure 5)  
6. Hold metal channel on anchor (F) flat alongside plastic  
strapsandslidechannelthroughhole. (SeeFigure3)  
10. Repeat steps 6 through 9 for each mounting hole.  
5
 
JWDSK Series  
Installation Instructions  
Display Installation  
Steel Stud  
Drywall  
1. Determine mounting pattern on display.  
Plastic Cap  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL  
INJURY AND DAMAGE TO EQUIPMENT! DO NOT  
substitute hardware. Use only hardware supplied by  
manufacturer!  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT! Screw  
length must not exceed the depth of threaded mounting insert  
in display.  
Plastic Straps  
Anchor Metal Channel  
WARNING: OVERTIGHTENING OF SCREWS CAN  
DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL  
INJURY AND DAMAGE TO EQUIPMENT! DO NOT over  
tighten screws when installing interface bracket.  
SIDE VIEW  
Figure 5  
NOTE: If the display being installed has a 100x100 VESA  
mounting pattern, no interface bracket is required and  
the display can be mounted directly to the mounting  
plate as outlined below.  
11. Place mount over anchors and align mounting holes in  
display mount with holes in anchors. (See Figure 6)  
12. Place flat washer (E) onto Phillips pan head screws (D).  
13. Insert 1/4-20 x 1-3/4" Phillips pan head screw (D) with flat  
washer (E) through mounting hole in display mount and into  
anchor (F) and tighten until flush against mount. DO NOT  
overtighten!  
NOTE: If the display being installed requires an interface  
bracket, refer to the interface bracket installation  
instructions.  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Overtightening of  
mounting hardware can damage the steel studs. DO NOT  
overtighten mounting hardware!  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
DISPLAY FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Using screws of  
improper size may damage your display! Proper screws will  
easily and completely thread into display mounting holes.  
Ensure that screws are not too long.  
Steel Stud  
Drywall  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
DISPLAY FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread  
engagement in display may cause display to fall! Back out  
screws ONLY as necessary to allow installation of mounting  
plate!  
(E) x 4  
(D) x 4  
1. Start two M4 x 12mm Phillips pan head screws (included in  
hardware kit) into upper mounting holes in display back.  
(See Figure 7)  
NOTE: Leave at least 1/8" of each screw protruding out back  
of display.  
Display Mount  
Anchor Metal Channel  
SIDE VIEW  
Figure 6  
6
 
Installation Instructions  
JWDSK Series  
CAUTION: Ensure that adequate cable slack exists for  
movement of display, and that cables will not be pinched by  
installation of cover (B) or screws (C).  
2. Carefully insert cables in cavity located in lower portion of  
mount arm (See Figure 9).  
3. Using Phillips screwdriver, install cover (B) with two screws  
(C). (See Figure 9)  
1
x2  
Cable Path  
(typical)  
Figure 7  
2. Align two screws in display back with upper teardrop  
mounting holes in mounting plate.  
3. Place two screws in display back into upper teardrop  
mounting holes in display mounting plate and lower display  
until screws are seated in lower area of teardrop mounting  
holes. (See Figure 8)  
(B) x 2  
(C) x 4  
4. Install two screws through display mounting plate and into  
lower mounting holes in display back. (See Figure 8)  
5. Tighten all hardware.  
Figure 9  
ADJUSTMENTS  
Swing Arm  
PIVOT / SWING  
1. Using 3/16" hex key (G), slightly loosen or tighten the  
adjustment screw(s) as necessary. (See Figure 10)  
2
3
Adjustment Screws  
x 2  
4
Figure 10  
Figure 8  
6. Route cables and wires to display.  
CABLE MANAGEMENT  
1. Attach all cables to display.  
7
 
JWDSK Series  
Installation Instructions  
Adjust display Roll, Pitch, and YAW tension  
1. Disconnect all wires and cable from the display.  
2. Remove two Lower screws securing display to Centris cup.  
3. Loosen two Upper screws securing display.  
4. Lift display upward and away from mount.  
5. Using a hex head wrench turn the tension adjustment screw  
clockwise to increase tension, or counter-clockwise to  
decrease tension. (See Figure 11)  
6. Re-install display.  
Figure 11  
8
 
Installation Instructions  
JWDSK Series  
9
 
JWDSK Series  
Installation Instructions  
10  
 
Installation Instructions  
JWDSK Series  
11  
 
JWDSK Series  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378  
800.582.6480 / 952.894.6280  
877.894.6918 / 952.894.6918  
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands  
+31 (0)40 2668620  
Chief Manufacturing, a division of  
Milestone AV Technologies, Inc.  
+31 (0)40 2668615  
Asia Pacific  
A
Room 24F, Block D, Lily YinDu International Building  
LuoGang, BuJi Town, Shenzhen, CHINA.  
8832-000220 RevC  
©2008 Milestone AV Technologies  
06/08  
P
F
+86-755-8996 9226  
+86-755-8996 9217  
 

BenQ Projector MP625P User Manual
Black Box TV Video Accessories AC340A R2 User Manual
Black Decker Insect Control Equipment MR100 User Manual
Braun Coffee Grinder 4041 User Manual
Braun Iron SI 3120 User Manual
Briggs Stratton Switch Automatic Transfer Switch User Manual
Brocade Communications Systems Switch IPMC5000PEF User Manual
Bryant Furnace 355MAV User Manual
CDA Dishwasher CW493 BL WH SS User Manual
Chicago Electric Plumbing Product 93188 User Manual