Chief Manufacturing Indoor Furnishings FSA 100 User Manual

IN STAL LA TIO N I NST RUCT IONS  
Flat Panel Display Security Kit  
(FSA-1009 and KSA-1009)  
The flat panel display security kit replaces exposed  
hardware with security hardware.  
NOTE: In some installations (i.e. single arm mount) not  
all fasteners included in this kit will be required.  
The security accessory kit can be used on most flat  
panel configurations.  
The pivot/pitch mount and mounts that are equipped with  
a swing arm use the 4-inch security pivot bolts. Mounts  
that are equipped with a height-adjustable arm use the  
5-inch security pivot bolts. Some configurations can use  
both the 4-inch and 5-inch security pivot bolts.  
Security Parts Kit  
The security accessory kit is available for F-Series  
mounts and K-Series mounts.  
BEFORE YOU BEGIN  
x
CAUTION: To prevent damage to the mount, which could affect or void the Factory warranty, thoroughly  
study all instructions and illustrations before you begin to install the mount brackets. Pay particular  
attention to the “Important Warnings and Cautions” on Page 2.  
x
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-894-6280.  
CHIEF MANUFACTURING INC.  
8807-000025 (Rev. C)  
©2006 Chief Manufacturing  
06/06  
1-800-582-6480 952-894-6280 FAX 952-894-6918  
8401 EAGLE CREEK PARKWAY, STE. 700  
SAVAGE, MINNESOTA 55378 USA  
 
Installation Instructions  
FSA/KSA-1009  
CONTENTS  
TOOLS REQUIRED FOR  
INSTALLATION  
TOOLS REQUIRED FOR INSTALLATION .................3  
PARTS.......................................................................3  
DISPLAY SECURITY SCREWS.................................4  
Flush Mount............................................................4  
Recessed Mount.....................................................4  
INSTALL SECURITY PIVOT BOLTS..........................5  
Install 4-inch Security Pivot Bolts ............................5  
Install 5-inch Security Pivot Bolts ............................5  
Install 4-inch and 5-inch Security Pivot Bolts ...........5  
INSTALL SECURITY SET SCREWS..........................6  
Option I...................................................................6  
Option II..................................................................6  
x
x
x
1/8” Hex key wrench  
5/32” Hex key wrench  
3/16” Hex Key wrench  
NOTE: Other tools may be required depending on the  
method of installation.  
PARTS  
Prior to installing the security kit, unpack carton completely and verify the contents listed in Table 1. If you are missing  
any of the parts, contact Customer Service at 1.800.582.6480.  
Table 1. Security Parts Kit  
ITEM  
10  
DESCRIPTION  
Security Pivot Bolt, 4”  
QTY ITEM  
DESCRIPTION  
M4 x 12mm Security Screw  
M4 x 20mm Security Screw  
1/8” Hex Key  
QTY  
3
2
1
1
1
60  
70  
80  
90  
4
4
1
1
1
20  
Security Pivot Bolt, 5”  
30  
1/4-20 x 1/4” Security Screw  
1/4-20 x 5/8” Set Screw  
40  
5/32” Security Hex Key  
50  
5/16-18 x 3/4” Security Set Screw  
100 3/16” Security Hex Key  
10  
60  
70  
90  
40  
100  
50  
80  
30  
20  
Figure 1. Security Kit Parts  
3
 
Installation Instructions  
FSA/KSA-1009  
M4 x 12mm  
Security Screw  
(typical)  
DISPLAY SECURITY SCREWS  
Select the appropriate hardware from the security kit to  
secure your display. Select the procedure, listed below,  
that applies to your application.  
Centris  
Mount  
x
Flush Mount (no spacers required)  
Recessed Mount (spacers required)  
x
Flush Mount  
1. Verify that you have the correct parts.  
2. Remove two M4 x 12mm screws from the top  
mounting holes on the display.  
3. Install two M4 x 12mm security screws (60) into the  
top mounting holes on the display (see Figure 2).  
Display  
4. Repeat Steps 2 and 3 to install the two remaining  
M4 x 12mm security screws (60) into the bottom  
mounting holes on the display.  
Figure 2. Flushed Mount  
Recessed Mount  
1. Verify that you have the correct parts.  
NOTE: If your display uses a screw size other than  
M4 x 20mm, DO NOT use the M4 x 20mm  
security screws. Using the wrong screws could  
result in damage to your display.  
M4 x 20mm  
Security Screw  
(typical)  
2. Remove two M4 x 20mm screws from the top  
mounting holes on the display, exercising care to  
retain the two spacers beneath the Centris mount.  
Centris  
Mount  
3. Install two M4 x 20mm security screws (70) and two  
spacers into the top mounting holes on the display  
(see Figure 2).  
Spacers  
4. Repeat Steps 2 and 3 to install the two remaining  
M4 x 20mm security screws (70) into the bottom  
mounting holes on the display.  
Display  
Figure 3. Recessed Mount  
4
 
Installation Instructions  
FSA/KSA-1009  
INSTALL SECURITY PIVOT BOLTS  
Perform the applicable procedure to replace the regular  
pivot bolts with security pivot bolts. You will need the  
security hex keys (provided) to complete the installation.  
4” Security Pivot Bolts  
Centris  
Mount  
Small  
Washer  
Install 4-inch Security Pivot Bolts  
For swing arm models, replace the standard pivot bolts  
with security pivot bolts, as follows:  
NOTE: Do not remove the display (not shown) from the  
Pivot Pin  
Flat  
Washers  
Centris mount.  
1. Verify that you have the correct parts.  
Large  
Washer  
2. Remove the 4-inch pivot bolt from the Centris mount.  
Exercise care to retain the other parts shown in  
Figure 4.  
Nut  
3. Install the 4-inch security pivot bolt (10) at the  
Centris mount. Make sure the other parts are  
installed in place as shown in Figure 4.  
4. Repeat Steps 2 and 3 to install the second  
4-inch security pivot bolt (10) into the other end of  
the mount.  
Install 5-inch Security Pivot Bolts  
For lift arm models, replace the standard pivot bolts with  
security pivot bolts, as follows:  
Figure 4. Install 4-inch Security Pivot Bolt  
(Swing Arm Example)  
NOTE: Do not remove the display (not shown) from the  
5” Security Pivot Bolts  
Centris mount.  
Centris  
Mount  
1. Verify that you have the correct parts.  
2. Remove the 5-inch pivot bolt from the Centris mount.  
Exercise care to retain the other parts shown in  
Figure 5.  
Small  
Washer  
3. Install the 5-inch security pivot bolt (20) at the  
Centris mount. Make sure the other parts are  
installed in place as shown in Figure 5.  
Pivot Pin  
Flat  
Washers  
Large  
Washer  
4. Repeat Steps 2 and 3 to install the second  
5-inch security pivot bolt (20) into the other end of  
the mount.  
4” Security  
Pivot Bolt  
Nut  
Install 4-inch and 5-inch Security Pivot Bolts  
For models that have both 4-inch and 5-inch pivot bolts,  
do the following:  
NOTE: Do not remove the display (not shown) from the  
Centris mount.  
1. Verify that you have the correct parts.  
2. Remove and replace the regular pivot bolt with the  
applicable security pivot bolt (see Figure 5).  
Figure 5. Install 5-inch Security Pivot Bolt  
(Lift Arm Example)  
5
 
Installation Instructions  
FSA/KSA-1009  
INSTALL SECURITY SET SCREWS  
The security set screw is used to secure the pivot-pitch  
wall mount. You will need the security hex keys  
(provided) to install the security set screws.  
There are two different wall plates, which require  
different security requirements. Select the option that  
applies to your configuration.  
Option I  
NOTE: If your wall plate uses a 1/4-20 set screw,  
replace it with a 1/4-20 x 5/8” security set screw  
(40) and a 1/4-20 x 1/4” security screw (30).  
The existing set screw in the wall plate is too  
long to be used with the 1/4-20 x 1/4” security  
screw.  
1/4-20 x .625  
Set Screw  
1. Verify that you have the correct parts.  
2. Remove the existing 1/4-20 x 1/4” set screw from the  
wall plate.  
1/4-20 x .25  
Security Screw  
3. Install a 1/4-20 x 5/8” security set screw (40) and a  
1/4-20 x 1/4” security screw (30) into the wall plate in  
the order shown in Figure 6.  
Figure 6. Install Security Set Screws (Option I)  
Option II  
1. Verify that you have the correct parts.  
2. Remove the existing 5/16-18 x 3/4” set screw from  
the wall plate.  
3. Install the 5/16-18 x 3/4” security screw (50) in the  
wall plate (see Figure 7).  
5/16-18 x .75  
Security  
Set Screw  
Figure 7. Install Security Set Screws (Option II)  
6
 

Bel Canto Design Stereo Amplifier eVo2iTM User Manual
Blue Rhino Patio Heater 153300 User Manual
Bosch Power Tools Drill PS10 2 User Manual
BOXLIGHT Projector XD 9m User Manual
Braun Coffeemaker KF510 User Manual
Bravetti Toaster TO283H User Manual
Breville Juicer JE3 User Manual
Canon Photo Printer CLC2620 User Manual
Casio Computer Hardware DT X5 User Manual
Chamberlain Garage Door Opener WD822KLS 1 2 User Manual