Chief Manufacturing Doll SSM 295 User Manual

I N S T A L L AT I O N I N S T R U C T I O N S  
SSM-295 Interface Bracket  
SSM-295 Interface Brackets are designed for use with the MSP-EIK130 and MSP-EIK230 short throw wall mounts. See the specific  
installation instructions provided with the mount for additional installation information.  
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.  
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND  
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!  
(1) Interface Bracket  
(4) Spacer, .500 x .316 x .500  
(4) Screw, Phillips Flat Head, Machine, M4 x 20mm  
(4) Screw, Phillips Flat Head, Machine, M5 x 25mm  
= M4 screw locations  
= M5 screw locations  
Towards front  
of projector  
SSM-295  
Figure 1  
NOTE: All appropriate screws (See Figure 1) come pre-installed. DO NOT attempt to substitute and USE ONLY this pre-installed hardware  
for interface bracket installation.  
Installation Instructions  
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND  
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.  
1. Turn projector upside down on a flat surface.  
2. Place spacers over appropriate threaded inserts on bottom of projector.  
3. Place the interface bracket onto the spacers, aligning the mounting holes in the bracket with the spacers and threaded inserts in the bottom  
of the projector and ensuring that triangle in bracket points towards front of projector.  
4. Determine proper size screws to use with projector.  
IMPORTANT ! : Using screws of improper size may damage the projector. Properly sized screws will easily and completely  
thread into projector threaded inserts. See Figure 1 for proper placement of M4 and M5 screws.  
5. Position mounting screws through bracket, spacers and into appropriate threaded inserts in the projector. Tighten all fasteners at this time,  
securing the bracket to the projector.  
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.  
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes  
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use  
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or  
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.  
Chief Manufacturing, a products division of Milestone AV Technologies  
8401 Eagle Creek Parkway, Savage, MN 55378  
8800-002108 Rev01  
©2011 Milestone AV Technologies,  
a Duchossois Group Company  
08/11  
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918  
 

Black Box Computer Hardware KV1720A User Manual
Black Box Computer Monitor IC147A R2 User Manual
Black Decker Cordless Drill DR260 User Manual
Blanco Indoor Furnishings 509 337 User Manual
Canon Camcorder AF514XL S User Manual
Canon Camera Lens EF17 40MM F 4L USM User Manual
Canon Printer 5152B009 User Manual
Casio Musical Toy Instrument SP 32 User Manual
CDA Ventilation Hood CIN6 User Manual
Celestron Telescope OMNI XLT 102 User Manual